Valtorc -- Industrial Valves

VALTORC
1-866-VALTORC
770-423-7100
Fax 770-499-7483
PO Box 1928
3105 Carter Circle
Kennesaw GA 30144
email: controls9@aol.com

Industrial Valves

Compact Automated Industrial Valves
	Reactivity Exotic materials to resist corrosion and other undesired interactions. Complexity Innovative solutions for complex conditions requiring precision control Extreme Cold Cryogenic ranges down to -450°F. Standard and cold-box designs Extreme Heat +400°F to +1000°F. Call for applications above this range High Pressure 5,000 psi to 60,000 psi Electric Actuators On-off and modulating Torques to 4300 in lbs Weatherproof construction Mechanical stops Manual overrides

2" to 10" Cast Iron Full Port Ball Valves
ANSI B16.10	Stainless Steel ball and stem Positive shut-off / Teflon seats Blow-out proof stem Open or closed simple throttling Replaces gate valves – same end to end dimension Tapped actuator mounting pad Fused epoxy coating 490 lbs to 11,900 lbs torque

2" to 24" Knife Gate Valves
ANSI 150 lbs, Pressure 150 KPA	Full lug type, full port, resilient seat or metal Solid one piece all cast 316 SS body and top works Machine ground ultra thick gate jambs Beveled knife on metal seats Blow out proof knife Inline field actuation landing flange Adjustable packing pusher Each valve tested MSS-SP81 Thrust bearing to assist closure Bi-directional resilient seat Rising stem

2" to 12" Economy Dual Plate, Metal Hinge Check Valve
W.O.G. Service, 285 psi, 100°F	Standard cast steel or cast 316 SS body Dual plate valves give maximum strength with minimum opening time Full contact seats maintain positive shutoff at minimum working pressure Torsion springs assist valve closure, preventing flow reversal Shaft is of extra heavy duty, corrosion resistant construction Shaft supports with large bearings act as stops to prevent over travel of plates Thrust washers reduce friction and wear of valve plate hinges Cast Iron comes in sizes 2" to 48", psi 200, 200°F

2" to 48" Flanged Horizontal Swing Check Valve – Cast Iron
W.O.G. Service, 200 psi, 200°F	Conforms to MSS SP-71 End Flange Dimensions: ANSI B16.1 Face to Face Dimensions: ANSI B16.10 Cast iron body, cover, and disc Valve is provided with a bronze seat ring and disc ring, offers a more positive sealing effect than competitors' standard iron facing

2" to 12" Silent Wafer Check Valves – Cast Iron
Liquid Service, 400 psi, 180°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 16" Silent Globe Style Check Valves – Cast Iron, Flanged
Liquid Service, 200 psi, 150°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 30" Foot Valves
	Cast iron, 125 lb. ANSI Standard Available in carbon steel & stainless steel Buna-N o-ring provides a drop-tight seal Seating design provides positive shutoff at all pressure ranges without additional loading on the seal Heavy duty stainless steel screening, with flow area 3 to 4 times that of pipe area Silent operation, by design of disc, stroke and linear closing characteristics

1/2" to 12" Fire Safe Ball Valves
ISO 9001 Certified & API 607 / API 6FA / BS-6755 Part II Fire Safety	Flanged, two piece soft seated Full or reduced bore Actuator mounting pad as per ISO-5211 in Metric/UNC Multiple stem sealing Double body-gasket sealing Antistatic device stem to body stem to ball Blow-out proof stem Fire safe metal lip Specially designed seat ring Low operating torque High spherocity & excellent surface finish of ball gives positive shutoff

2" to 48" Butterfly Valves
ANSI 125/150 lbs, Zero Leakage Rate	Available in lug or wafer style 100% factory tested in both directions of operation to assure a zero leakage rate Extended neck design for ample application of insulation One-piece/uni-body construction of cast iron, optional ductile iron body Integral mounting flange will accept all styles of hand lever, mulit-turn manual gear and power operators/actuators Oil impregnated bronze stem bushings to assure long life One-piece resilient seat with molded in o-ring seal Suitable for open left or open right operation One-piece shaft design Butterfly standard with a hard back seat

2" to 24" Flanged Elastic Swing Check Valve – Ductile Iron
W.O.G. Service, 150°F Sizes 2" to 12": 200 psi Sizes 14" to 24": 150 psi	ANSI B16.1 and Class 150 or 250 Internal body is epoxy coated. Special coatings available upon request One-piece molded disc has a steel reinforced insert to ensure closure 100% uninterrupted flow in the open position One-piece disc hinge and flapper can be repaired without removal of the valve from the line Elastic check can be installed in a vertical or horizontal pipeline

2" to 12" Wafer Swing Check Valve – Cast Iron
W.O.G. Service, 285 psi, 100°F	Accurately machined 316 SS clapper Spring loaded clapper assures instantaneous closure to reversing flow, preventing build-up of momentum Hinge pin design assures free movement of the clapper and eliminates seizure under extreme conditions Soft seal inserts are standard for positive sealing of hard-to-hold solvents and fluids Lifting hook eye on 8" to 12" valves

2" to 24" Silent Wafer Check Valves – Cast SS & Cast Steel
Liquid Service, 740 psi, 100°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 12" Silent Globe Style Check Valves – Cast SS & Cast Steel, Flanged
Liquid Service, 285 psi, 100°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

Flexible Expansion Joints & Pump Connectors

VALTORC
1-866-VALTORC I 770-423-7100 I Fax 770-499-7483
PO Box 1928 I 3105 Carter Circle I Kennesaw GA 30144
email: controls9@aol.com

© 2007 VALTORC, All Rights Reserved