Valtorc -- Gate/Globe/Check Valves

VALTORC
1-866-VALTORC
770-423-7100
Fax 770-499-7483
PO Box 1928
3105 Carter Circle
Kennesaw GA 30144
email: controls9@aol.com

Gate, Globe & Check Valves

2" to 12" Economy Dual Plate, Metal Hinge Check Valve
W.O.G. Service, 285 psi, 100°F	Standard cast steel or cast 316 SS body Dual plate valves give maximum strength with minimum opening time Full contact seats maintain positive shutoff at minimum working pressure Torsion springs assist valve closure, preventing flow reversal Shaft is of extra heavy duty, corrosion resistant construction Shaft supports with large bearings act as stops to prevent over travel of plates Thrust washers reduce friction and wear of valve plate hinges Cast Iron comes in sizes 2" to 48", psi 200, 200°F

2" to 48" Flanged Horizontal Swing Check Valve – Cast Iron
W.O.G. Service, 200 psi, 200°F	Conforms to MSS SP-71 End Flange Dimensions: ANSI B16.1 Face to Face Dimensions: ANSI B16.10 Cast iron body, cover, and disc Valve is provided with a bronze seat ring and disc ring, offers a more positive sealing effect than competitors' standard iron facing

2" to 12" Silent Wafer Check Valves – Cast Iron
Liquid Service, 400 psi, 180°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 16" Silent Globe Style Check Valves – Cast Iron, Flanged
Liquid Service, 200 psi, 150°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 30" Foot Valves
	Cast iron, 125 lb. ANSI Standard Available in carbon steel & stainless steel Buna-N o-ring provides a drop-tight seal Seating design provides positive shutoff at all pressure ranges without additional loading on the seal Heavy duty stainless steel screening, with flow area 3 to 4 times that of pipe area Silent operation, by design of disc, stroke and linear closing characteristics

Forged Steel & Stainless Steel Gate, Globe and Check Valves
Sizes 1/2" to 2" NPT & SW End Connections 316L Forged Stainless Steel and Forged Steel Pressure: Up to 1975 PSIG f.St. & Up to 1600 PSIG F.S.St. Temperature: 100°F to 1000°F F.St. & 100°F to 850°F F.S.St. Class 800 ASTM A182/316L Stainless Steel A105 Forged Steel Bolted Bonnet/Cover

2" to 24" Flanged Elastic Swing Check Valve – Ductile Iron
W.O.G. Service, 150°F Sizes 2" to 12": 200 psi Sizes 14" to 24": 150 psi	ANSI B16.1 and Class 150 or 250 Internal body is epoxy coated. Special coatings available upon request One-piece molded disc has a steel reinforced insert to ensure closure 100% uninterrupted flow in the open position One-piece disc hinge and flapper can be repaired without removal of the valve from the line Elastic check can be installed in a vertical or horizontal pipeline

2" to 12" Wafer Swing Check Valve – Cast Iron
W.O.G. Service, 285 psi, 100°F	Accurately machined 316 SS clapper Spring loaded clapper assures instantaneous closure to reversing flow, preventing build-up of momentum Hinge pin design assures free movement of the clapper and eliminates seizure under extreme conditions Soft seal inserts are standard for positive sealing of hard-to-hold solvents and fluids Lifting hook eye on 8" to 12" valves

2" to 24" Silent Wafer Check Valves – Cast SS & Cast Steel
Liquid Service, 740 psi, 100°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

2" to 12" Silent Globe Style Check Valves – Cast SS & Cast Steel, Flanged
Liquid Service, 285 psi, 100°F	Closes before the pump stops completely to prevent flow reversal to eliminate water hammer and system surges Quiet operation Guided discs Vertical or horizontal installation

Threaded Gate, Globe and Swing Check Valves
	Sizes 1/4" to 3" NPT & SW end connections 316 stainless steel Pressure: up to 250 PSI WOG Temperature: up to 350°F Class 20 ASTM A351 Inside screw and screwed bonnet Non-rising stem Solid wedge disc

Flanged Gate, Globe and Swing Check Valves

Flanged Gate

Flanged Globe

Flanged Swing Check

VALTORC
1-866-VALTORC I 770-423-7100 I Fax 770-499-7483
PO Box 1928 I 3105 Carter Circle I Kennesaw GA 30144
email: controls9@aol.com

© 2007 VALTORC, All Rights Reserved